Wifi Aruba AP-335
Mã SP: AP012
1,350,000 ₫
– Tình trạng: 95%, no box.
– Phụ kiện: đế treo tường. Nguồn POE AT + 150.000.
– Giá trên không bao gồm VAT.
Hết hàng
Bảo hành: 1 năm
– Wifi Aruba AP-335, chuẩn AC2300 wave 2, 8 anten, 1 x LAN 5Gb và 1 x LAN 1Gb.
– Quản lý tập trung, chịu tải cao 100 thiết bị.
SPECIFICATIONS
- AP-335 (controller-managed) and IAP-335 (Instant):
– 5GHz 802.11ac 4×4 MIMO (1,733 Mbps max rate)
and 2.4 GHz 802.11n 4×4 MIMO (600 Mbps max rate)
radios, with a total of twelve integrated omni-directional
downtilt antennas
WI-FI RADIO SPECIFICATIONS
- AP type: Indoor, dual radio, 5 GHz 802.11ac 4×4 MIMO
and 2.4 GHz 802.11n 4×4 MIMO
– In addition to 802.11n, the 2.4 GHz radio supports all
802.11ac features as well (proprietary extension)
- Software-configurable dual radio supports 5 GHz (Radio 0)
and 2.4 GHz (Radio 1)
- 5 GHz:
– Four spatial stream Single User (SU) MIMO for up to
1,733 Mbps wireless data rate to individual 4×4 VHT80
or 2×2 VHT160 client devices
– Four spatial stream Multi User (MU) MIMO for up to
1,733 Mbps wireless data rate to up to three MU-MIMO
capable client devices simultaneously
- 2.4 GHz: Four spatial stream Single User (SU) MIMO for
up to 600 Mbps wireless data rate to individual 4×4 HT40
client devices
- Support for up to 256 associated client devices per radio,
and up to 16 BSSIDs per radio
- Supported frequency bands (country-specific
restrictions apply):
– 2.400 to 2.4835 GHz
– 5.150 to 5.250 GHz
– 5.250 to 5.350 GHz
– 5.470 to 5.725 GHz
– 5.725 to 5.850 GHz
- Available channels: Dependent on configured
regulatory domain
- Dynamic frequency selection (DFS) optimizes the use of
available RF spectrum
- Supported radio technologies:
– 802.11b: Direct-sequence spread-spectrum (DSSS)
– 802.11a/g/n/ac: Orthogonal frequency-division
multiplexing (OFDM)
- Supported modulation types:
– 802.11b: BPSK, QPSK, CCK
– 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
- Transmit power: Configurable in increments of 0.5 dBm
- Maximum (aggregate, conducted total) transmit power
(limited by local regulatory requirements):
– 2.4 GHz band: +24 dBm (18 dBm per chain)
– 5 GHz band: +24 dBm (18 dBm per chain)
– Note: conducted transmit power levels exclude antenna
gain. For total (EIRP) transmit power, add antenna gain
- Advanced Cellular Coexistence (ACC) minimizes
interference from cellular networks
- Maximum ratio combining (MRC) for improved
receiver performance
- Cyclic delay/shift diversity (CDD/CSD) for improved
downlink RF performance
- Short guard interval for 20 MHz, 40 MHz, 80 MHz and
160 MHz channels
- Space-time block coding (STBC) for increased range and
improved reception
- Low-density parity check (LDPC) for high-efficiency error
correction and increased throughput
- Transmit beam-forming (TxBF) for increased signal
reliability and range
- Supported data rates (Mbps):
– 802.11b: 1, 2, 5.5, 11
– 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
– 802.11n: 6.5 to 600 (MCS0 to MCS31)
– 802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4 for
VHT20/40/80, NSS = 1 to 2 for VHT160)
- 802.11n high-throughput (HT) support: HT 20/40
- 802.11ac very high throughput (VHT) support:
VHT 20/40/80/160
- 802.11n/ac packet aggregation: A-MPDU, A-MSDU
WI-FI ANTENNAS
- AP-334/IAP-334: Four RP-SMA connectors for external dual band antennas. Internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 2.3 dB in 2.4 GHz and 1.2 dB in 5 GHz.
- AP-335/IAP-335
– Four (vertically polarized) integrated 2.4 GHz downtilt omni-directional antennas for 4×4 MIMO with peak antenna gain of 3.8dBi per antenna.
– Each 5 GHz radio chain has both a vertically and a horizontally polarized antenna element; AP software automatically and dynamically selects the best set of elements for each data packet transmitted or received.
DATA SHEET
ARUBA 330 SERIES WIRELESS ACCESS POINTS
4
– Four integrated vertically polarized 5 GHz downtilt omnidirectional antennas for 4×4 MIMO with peak antenna
gain of 4.9dBi per antenna
– Four integrated horizontally polarized 5 GHz downtilt
omni-directional antennas for 4×4 MIMO with peak
antenna gain of 5.7dBi per antenna
– Built-in antennas are optimized for horizontal ceiling
mounted orientation of the AP. The downtilt angle for
maximum gain is roughly 30 degrees.
– Combining the patterns of each of the antennas of the
MIMO radios, the peak gain of the effective per-antenna
pattern is 1.6dBi in 2.4 GHz and 2.5dBi in 5 GHz.
OTHER INTERFACES
- One HPE Smart Rate port (RJ-45, maximum negotiated
speed 5Gbps)
– Auto-sensing link speed (100/1000/2500/5000BASE-T)
and MDI/MDX
– 2.5Gbps and 5Gbps speeds comply with NBase-T and
802.3bz specifications
– PoE-PD: 48 Vdc (nominal) 802.3at PoE
- One 10/100/1000BASE-T Ethernet network interface (RJ-45)
– Auto-sensing link speed and MDI/MDX
– PoE-PD: 48 Vdc (nominal) 802.3at PoE
- Link aggregation (LACP) support between both network
ports for redundancy and increased capacity
- DC power interface, accepts 1.35/3.5-mm center-positive
circular plug with 9.5-mm length
- USB 2.0 host interface (Type A connector)
- Bluetooth Low Energy (BLE) radio
– Up to 4 dBm transmit power (class 2) and -91 dBm
receive sensitivity
– Integrated antenna with roughly 30 degrees downtilt
and peak gain of 5.1 dBi (AP-334/IAP-334) or 2.2 dBi
(AP-335/IAP-335)
- Visual indicators (tri-color LEDs): for System and Radio status
- Reset button: factory reset (during device power up)
- Serial console interface (RJ-45, RS232)
- Kensington security slot
POWER SOURCES AND CONSUMPTION
- The AP supports direct DC power and Power over
Ethernet (PoE)
- When both power sources are available, DC power takes
priority over PoE
- Power sources are sold separately
- Direct DC source: 48Vdc nominal, +/- 5%
– Interface accepts 1.35/3.5-mm center-positive circular
plug with 9.5-mm length
- Power over Ethernet (PoE): 48 Vdc (nominal)
802.3af/802.3at compliant source
– When using IPM, the AP may enter power-save mode
with reduced functionality when powered by a PoE
source (see details on Intelligent Power Monitoring in
this datasheet)
– Without IPM the AP will apply some fixed restrictions
when using PoE:
> The USB interface is disabled when using an 802.3at PoE power source
> The USB interface and second Ethernet port are disabled, and both radios operate in 1×1 mode when using an 802.3af POE power source
- Maximum (worst-case) power consumption: 25.3W
(802.3at PoE), 13.2W (802.3af PoE) or 25W (DC)
– Excludes power consumed by external USB device (and
internal overhead); this could add up to 5.9W (PoE or
- DC) for a 5W/1A USB device
- Maximum (worst-case) power consumption in idle mode:
10.9W (PoE or DC)
MOUNTING
- The AP ships with two (black) mounting clips to attach to a
9/16-inch or 15/16-inch flat T-bar drop-tile ceiling.
- Several optional mount kits are available to attach the
AP to a variety of surfaces; see the Ordering Information
section below for details
MECHANICAL
- Dimensions/weight (unit, excluding mount accessories):
– 225mm (W) x 224mm (D) x 52mm (H)
8.9” (W) x 8.9” (D) x 2.0” (H)
– 1150g/41oz
- Dimensions/weight (shipping):
– 335mm (W) x 290mm (D) x 85mm (H)
13.2” (W) x 11.4” (D) x 3.35” (H)
– 1750g/62oz
ENVIRONMENTAL
- Operating:
– Temperature: 0° C to +50° C (+32° F to +122° F)
– Humidity: 5% to 93% non-condensing
- Storage and transportation:
– Temperature: -40° C to +70° C (-40° F to +158° F)